X Email Mobile
Price Negotiable
A new item has been added to your Shopping Cart. You now have items in your Shopping Cart.
Yiwu Wuhao Office Equipment Firm 12yr.
Main Products:Laminating Machine,Paper Cutter,Cementing Machine,Printer
Contacts:钱林木Chat
Mobile:86-15325960833
E-mail: WeChat:gdvx123
Address:24298 , 7 Street, 2 F, 51 Gate, International Trade Mart (District 3).
Related items
一、功能:
本机用于对不干胶制品的表层直线分条切割和用于对纸张的虚线切割、及书本封面的压痕。本机可用滚切刀滚切和剃须刀划切两种方式。齿形滚切片用于纸张的虚线切割。本机设置调速装置可将滚筒转速从50~~290转/分无级调速。
二、操作程序:
1、本机选用220V电源。将随机电源一端插入机架上的插座另一端与电源接通开启主电源开关,机器就可以正常运转。速度调节旋钮用于调节滚筒的旋转速度,顺时针方向旋转速度增加,反之速度减慢。
2、切割工件时先旋转手轮把工件引入滚筒使之停留在分割线位置。根据被割工件的尺寸要求选择标尺读数调整刀片的位置和高度。用手轮旋转试割直到符合要求,然后开机切割。先慢速运转,逐渐提速到正常速度。本机具有压痕功能,只要将随机两个压痕轮换上调整好位置就能起到压痕作用。
三、使用注意事项:
1、刀架紧固在六角滑道上。定位出螺钉的紧固力度要适当。用力过度会损坏刀架。
2、剃须刀安装位置应与橡胶轮匹配。
3、调整刀片位置时应注意刀片刀口不能与滚筒直接接触以免损坏刀片刀口和滚筒表面。
4、工作时双手与割刀保持一定距离防止发生伤害事故。
5、定期打工左侧盖板。检查调整皮带的松紧程度。
6、请用随机的电源线连接电源。供滚切机电源的插座必须专用,不允许其它设备并入专用电源插座。
型 号 |
H-500 |
切割宽度mm |
500mm |
最小切割宽度mm |
6mm |
滚筒转速(转/分) |
50-290 |
电机功率(W) |
180W |
电源 |
220V 50HZ |
A, function:
The surface of the adhesive product line for strip cutting and indentation and the dotted line for books on paper cutting, cover the machine. The machine can rollcutter hobbing and shaving razor incision in two ways. Toothed roll sections forpaper cut line. The machine is provided with a speed regulating device can beroller speed from 50~~290 RPM stepless speed regulation.
Two, the operation procedure:
1, the selection of 220V power supply. The random power end is inserted into asocket on the frame and the other end of the power supply is switched on to open the main power switch, the machine can normal operation. Speedadjustment knob for adjusting cylinder rotating speed, rotating speed alongclockwise to increase, whereas slow down.
The 2, cutting the workpiece when the first rotating the handwheel to artifacts introduced into the drum to stay in the dividing line of position. According to the requirements of cut workpiece size selection scale reading adjusting the position of the blade and height. Using the handwheel rotation test tapping until it meets the requirements, and then boot cut. First, the slow running speed, gradually to normal speed. The machine has the function of indentation, as long as the two random indentation rotation adjustment good location will be able to play the roleof indentation.
Three, the use of attention to matters:
1, in the six corners slide holder fastening. The positioning screw fasteningstrength should be appropriate. Excessive force will damage the knife.
In 2, shaver installation location should match with the rubber wheel.
3, adjust the blade position should be paid attention to when the blade edge can not directly contact with the roller blade edge and the surface of the roller so as to avoid damage.
4, work hands and the cutting knife to maintain a certain distance to prevent the occurrence of injury accidents.
5, regular work left cover. Check and adjust the degree of tightness of the belt.
6, please connect power supply for power line random. Socket for hobbingmachine power supply must be dedicated, do not allow other devices into thespecial power supply socket.
Model No.
H-500
The cutting width mm
500mm
The minimum cutting width of MM
6mm
Drum rotational speed (RPM)
50-290
Motor power (W)
180W
Power Supply
220V 50HZ
Update time:
TOP