Packing: Blister Card

Dear, the total length of the baby is about 24cm, and the length of the steel pipe is about 10cm.

Purpose: Gas stove, liquefied gas stove, lighter, birthday candles, fire-starting in the wild, heating stoves, fireworks and firecrackers, also used in hotels and restaurants.

Shop, tobacco and alcohol advertising gifts - widely used, low price, safe and quick flame point

Use Range

1. Cooking and Diet

2. Lighting a grill and starting a fire

3. Defrosting and Thawing

4. Craftsmanship and Model Making

5. Welded Pipe Joint

6. Paint Peeling

Notes

1. The lighter contains flammable gas under pressure. Please keep it away from children. 2. Do not pierce or throw the lighter, and do not throw it into fire. 3. Please use it in a well-ventilated environment, and pay attention to flammable items. 4. The fire head direction is strictly prohibited from facing the face, skin, and clothing and other combustible materials to avoid danger. 5. When lighting, please identify the position of the fire outlet, and press the ignition appropriately. Different models of lighters use different ignition methods: straight, side, and edge. For gasoline machines, it should be quickly rubbed on the sanding wheel, and for loud machines, it should be quickly rubbed with the thumb from right to left on the roller. 6. When using, if there are smoke, ash, and other debris falling into the fire outlet, it should be promptly blown to remove the debris, otherwise it may cause poor ignition. 7. For loud and gasoline lighters, if the lid is opened, the gas begins to escape. Therefore, when not igniting, please ensure that the lid is tightly closed for storage. 8. This product is not suitable for lighting, and please do not burn for more than 1 minute to avoid high temperature burns. 9. Do not leave the lighter in a high-temperature environment for a long time (50 degrees Celsius).Fahrenheit 122 degrees), and avoid direct sunlight for a long time, such as around the stove, the enclosed carriages and trunks in the outdoor; 10, due to the climate restrictions on the burning conditions in the area above 3000 meters, the ignition performance of windproof and direct-type lighters will be greatly affected. At this time, it is recommended to use open flame lighters; 11, when using craft-type lighters such as desk-style, it should be clear about the position of the flame outlet, pressing, air intake, and flame regulator to ensure correct use; 12, it should be used with qualified butane gas, poor-quality gas may damage the lighter or reduce its service life.

Regulate the flame

1. When using the product, the flame height may vary slightly due to the decrease in gas content and changes in the surrounding environmental temperature. This is a normal phenomenon, and you can adjust the flame height appropriately. 2. The normal flame height for use should be adjusted to: for windproof and direct-stream lighters, 1.5-2.5 cm; for loud, gasoline, and open flame lighters, 2.5-4.0 cm. 3. If you need to adjust the flame height, please use a flathead screwdriver to align with the recess of the flame regulator. If the lighter has a regulation ring, you can adjust the flame height directly by turning the ring in the direction of the arrow (-) clockwise to lower the flame height, or counterclockwise to increase the flame height. Note: rotating counterclockwise cannot exceed half a circle beyond the normal flame height. Otherwise, it may damage this product. 4. For gasoline lighters, the flame height should be controlled by adjusting the height of the ignition wick. If the flame height is too high, you can trim the wick slightly with scissors; if the flame height is too low, you can appropriately pull out the wick.

Gas filling method

1. When refilling, there must be no sparks or fire sources around to ensure safety. Do not smoke while refilling; 2. Use qualified butane gas. Poor-quality gas may damage the lighter or reduce its service life; 3. For standard models, hold the lighter upside down, align the gas bottle's outlet with the lighter's inlet, cover it, and press a few times, each time for about 2 seconds. If the gas cannot be added, it may be because there is excess air in the tank. In this case, you can vent the air by pressing the inlet with a small screwdriver quickly 1-2 times, and then refill the gas; 4. For loud models, first loosen the screw cover of the inlet with a flat-headed screwdriver, and then follow the above steps. After refilling, the screw cover should be leveled, not too tight; otherwise, it will cause the lid to be not tightly closed and the sound of the lid to be not crisp, and it will also make the gas escape. For the deluxe loud model, use a special air mouth to refill; 5. When refueling the gasoline engine, open the lid, pull out and reverse the engine, lift the outer sponge to add the appropriate amount of gasoline, wait for the gasoline to penetrate the inner sponge, cover the outer sponge, and then put it into the engine shell; 6. After refueling various lighters, wait at least 1 minute to allow the new gas to adjust to room temperature, and wait for the residual gas on the surface of the lighter to completely evaporate before igniting. If you ignite immediately, it may cause the residual gas on the surface of the lighter to ignite, causing unnecessary danger. If the flame height is too high or too low when using after refueling, it is normal. You can adjust the flame height appropriately.

Replace the flint in the gas lighter.

1. When igniting, there is not enough spark to ignite the gas. Consider replacing the striking stone. 2. For the standard type of loud machine: Press your finger continuously to slide the sliding block to the bottom of the machine cover, turn the lighter upside down, gently shake, and pour out the old striking stone from the striking stone slot, and replace it with new striking stone. 3. For the fitted type of loud machine and gasoline machine: The striking stone tightening screw of the fitted type loud machine is located at the rear side of the head cover, and the tightening screw of the gasoline machine is located at the bottom of the engine core. When using a crosshead screwdriver to slowly rotate out the tightening screw, it is necessary to hold the screw with your fingers to prevent the spring below from pushing the screw away. After replacing the new striking stone, when rotating the screw in, it is also necessary to protect the screw and spring with your fingers. 4. To verify if the operation is correct: quickly ignite to rub the striking stone, if you can produce a large amount of sparks, it indicates that the striking stone has been replaced correctly. Otherwise, you can adjust the screw appropriately to ensure that the striking stone is in the correct position, and then verify again.

Maintenance and Care

1. Please keep it in a place where children cannot reach; 2. Because it uses high-pressure combustible gas, it is prohibited to hit or place it in fire, and it shall not be placed in a place with a normal temperature of 55℃ or above; 3. Please do not rub it with other metal objects, otherwise it is easy to damage the surface protection layer. It is prohibited to throw, drop or fall this product, otherwise it may cause damage to the structure and function; 4. This product is not waterproof, please do not place it in water/acid/alkali/greasy and humid environments.