Product description:

The hand spraying membrane is a kind of natural dry elastomer coating agent, also known as liquid membrane, you can spray the inside and outside the body, wheels, auto accessories, free when you don't need to peel off. Moisture, acid resistant, abrasion, corrosion and protective effects on paintwork and wheels have very good, always bright clean like new!

Chameleon wheel wrap vinyl click here to enter

Product features:

Germany Edward paint production company, construction is simple, color gorgeous, hiding power, feel free to change color, the film is easy to clear, free DIY colour spray, fun, and full of personality. Nontoxic, not to hurt the original paint.

Product use:

Suitable for car wheels color-sprayed

Method of use:

1 Remove wheel hub grease, wax, dirt, dust, rust stains, sprayed surface should be flat and smooth, and does not absorb water. Cover well sprayed areas.

2. before spraying should shake the tins for at least 45 seconds, so the tank coating mix evenly from the sprayed surface 15-20CM , Pressed uniform spray nozzle back and forth with your index finger.

3. 建议喷涂 3-5 遍，喷涂厚度 30-35UM 以完全遮盖原色为佳。

4. spray again should not be too large, thin should spray until dry and then spray 2 layers or cause sagging, orange peel blemish traces.

5. 建议循环施工，每个轮毂上一遍后，在循环喷第 2 遍，第 3 遍 … ……

6. If not sprayed out at a time, please turn the jars upside down before storing, push down nozzle 3 seconds, clean valves to prevent clogging.

Peeling:

Available plastic scraper gently scrape off the paint film or business card paper, not with sharp hard object falling off, corners of the small film available alcohol { ethanol } , pulp oil cleanser to remove.

Notes:

1. optimum spray environment to 20-25 ° c , temperatures bottom too high can affect the results

Please first try spraying small area, confirm that no effects on the low wood, large area coating. This product is only limited to wheels.

2. If splashed into the eyes, rinse immediately with plenty of water and taken to hospital. Touch free toothpaste or washing paste cleaning.

3. inhalation of exhaust gas or swallowing solids can have a stimulating effect on the body . Please air flowing out of the construction and the wearing of face masks and gloves.

4. spray aerosol cans must be guaranteed when standing on horizontal angle shall be not less than 45 °.

5.本品为高压制品，应处于 40 ° C 以下使用存放。 Please do not put it in the car, away from sources of heat and open flames, precise exposure, away from children, serious puncture or burn pots.

6. the wheels do not use on surfaces under high temperature conditions.

7. this product is an aerosol product, net weight and gross weight over time changed contents loss rate isless than or equal to 2 years.

购买建议 ： 13-15 寸轮毂需要 2-3 瓶

16-18 寸轮毂需要 3-4 瓶

19-20 inch wheels need 4-5 bottles

Spray the thicker texture as you can, and also prevents scratches and more beautiful

Can also spray it left rear-view mirror, or other small items .

Product advantages:

1. direct spray, without dilution, there are equipped with spray guns, easy to operate, especially suitable for DIY in a stock car.

2. without grinding wheel surface, without dismantling wheels, simply rinse spray directly, directly when you don't like tearing off, wheels still fresh on the surface.

3. better effects than the paint, forming more texture, the surface is frosted matte.

This product can also be used for the following areas:
products: seal and protect wood from climate impacts and prevent cracking.
Metal products:reduce wobble, eliminating mixed sound, anti-corrosion, insulation, heat insulation.
Glass products:preventing broken glass (transparentPlasti Dip)
rope/braid:weather-resistant, prevent decay and damage.
Plastic products: protected soft surface is not scratched.
Rubber products: resistant to wind and rain, and wear resistant.

Map: weather-proof to prevent breakage.
Stock car: waterproof, wear-resistant, not to hurt the car and can be peeled off at random, does not affect the car's status. To protect the paint,rather than to beautify the paint

Note: due to the spraying membrane is no ordinary paint, do not use a sharp object poked touch, while cleaning the wheels do not use sharp implements, such as tire brush cleaning wheel .

Colour correction can tear the spraying membrane construction process and FAQ

Winter cold spray is bad what do you do?

Analysis:as cans of spray membrane in the body in a liquid state, rendering blown out meteorology, this process is the need to heat. When the winter cold tank heat absorbed by the ejected liquid is not enough atomization variation; liquid is sprayed onto the surface when will suck a lot of heat on the surface of the object, so drying is slow, water surface, sometimes even bubbles can occur, larger particles or droplet.

Solution:irrigation in 25-30 degrees 5-10 minutes immersion in warm water before construction, aerosol would be very delicate; used after the spray to the surface the air tube and other auxiliary equipment spray coating baking for 40 seconds, then continue spraying, quick drying, spray effects.

 Gag appears problem how to solve?

Causes:1, do not shake before spraying, liquid deposits blocking the pipeline. 2, spraying glass bead breaking gag caused shaking too much before. 3, do not use up spray and cleaning nozzles are stored. 4, the expiry date and contents back to rough in valves.

Precautionary measures:1, shake well before spraying. 2, moderate shaking when the tank. 3, disposable unused first jet upside down for 3 seconds, upright storage. 4, not upside down or on its side in the stored procedure.

Correction:first try to replace nozzle if this does not solve the problem, just pull the nozzle, turn the tank upside down so that the nozzle hole and squeezing, ionizes the ejected fully jam sauce, topped with sprinkler heads can be.

 Spray up to do?

Reasons:1 pour, spray with spray phenomena. 2, when the spray tank to tilt, angle of more than 45 °. 3, storage time is too long, the expiry date. 4, bending of tubes and nozzles in the direction of the valve holes in opposite directions.

Precautionary measures:1, master the correct spraying, avoid spraying. 2, the control tank and horizontal angles greater than 45 °. 3, in the period of use. 4, 180 ° rotating sprinkler spray.

  How to avoid sand and dirt in the wheel surface after spraying?

Cause analysis and solution:first of all, in indoor enclosed construction for a clean environment, eliminate mosquitoes in the construction process on the fly to the spraying membrane. Secondly, you must first put the wheel hub on stubborn before construction sand and clean the dirty spots, well along the wheel cleaning agent is recommended for processing. Again, in this process, please do not touch the film, spraying distance between nozzle and wheel surfaces properly, control in the 15-25cm Department, to prevent too close, the impact is too strong and cause spraying membrane surface is similar to the feeling of sand.

  After construction are darker in color with light color is all about?

Causes:1, construction technology is not mature, uneven spraying. 2 poor coverage, individual colors, such as Brown's fluorescent green, fluorescent yellow, movement (fluorescence) color series. 3, the wheels darker, or color. Driving wheel in individual parts wear tough surface will be rough and dull, the construction would be difficult to cover when and wear less of the surfaces smooth, easy to cover, this can also cause color differences.

  Precautions:to block-by-block spray in place during construction, every times must be sufficiently covered, paying particular attention to round corner positions on both sides, should be in place and even, in addition, carry out the spraying membrane construction, possess good spray technique. Spraying fluorescent series before spraying film, use the corresponding standard color base, such as spraying before the rapid fluorescent yellow, before spraying the bright yellow; when wheel wear and color, use a white base (full Uniform covered the wheels dirty spots on the surface), then spray the color you want.

 Wheel side of the edge? If accidentally sprayed onto the tires will not be affected?

Card and hub junction (hub edge) spray when you want to pay particular attention to, this site should be sprayed about 4 times. Aim the nozzle when spraying card and hub junction, the contents fully spurting into the gap in (note that control depress not out) around the wheel spray around it again. Then spraying other parts stay dry, to the aperture ring spray it again. Then according to this method, gaps need to be sprayed about 4 times in total, covering it concrete a few times to wheel around, the whole wheel uniform color prevails. If accidentally injected into the tire is OK, you can use a cloth to wipe.

  Demolition card or plastic spray coating started going to deal with this situation?

Entire sprayed spray but not when it is dry, immediately place all cards removed (blocked brake discs of plastic films or newspapers should also be sprayed out immediately after the wheels inside out from under the car chassis), thus avoiding a card and plastic film after drying with membrane layer above the wheels adhesion and lifting the entire film.

If you want to spray excessive color or gradient color, two colors at the same time: spray

When sprayed over or gradients, or gradient line requirements are not too high (not rendered straight line) or a line if it is not obvious, two colors can be sprayed simultaneously.

  Spray to do before you do a coat of primer? How should such as spraying white construction?

Some coverage is poor color (fluorescent series) need to base (is called a coat of primer). Fluorescent color standard color sprayed before spraying spraying spraying membrane such as spraying fluorescent yellow before, you should spray 1-2, regular yellow, before the spray to green, you should spray 1-2, regular green spraying film. Spray white (ivory) without base, effect of light which is blown out.

  Scratches, later have a way to repair it?

If small scratches, dust dirt cleaned the surface, again using the same color sprayed coating from scratches 20-25cm offices have to spray it one or two times.

If it is a deep scratch (already visible hub character), first clean the surface along the scratch 15cm set spray it again until dry and then spray it again, be repaired under similar circumstances, then the entire wheel spray thin again, so that you can prevent chromatic aberration, and spray evenly.

 Spray paint is there harm? Need to pay attention to?

Color spray can tear film on paint can be sprayed, but must be an original car paint or paint, bad paint is not allowed to spray. Feel free to tear off when it is not needed, leaving no trace, not damage to the paint surface, insulating, shock-proof, and can play a noise reduction effect.

 Spray up how to maintain? Need to pay attention to what issues?

Construction please use a neutral washing liquid after washing, use a soft washcloth or sponge, do not use hard brushes, washing car wheels Rod edge should be handled with care. Do not glue removers, asphalt, asphalt cleaner, solvents, such as alcohol, gasoline and diesel on the spraying membrane liquid.

  Spraying film tear how bad situations?

On one hand, colour correction can tear the spraying membrane is a rubber coating agent, attributes are color and can tear, best time in 3-6 months and if this time is exceeded, rubber ages, bad tearing may occur, it is recommended that often change color. The other hand, if sprayed too thin, layer thick enough to it of each other to form, there will be is bad won't RIP or tear off situation. We recommend spraying around 6 times during the construction or a wheel spray tank 1-look, which tore the thickness of absolute good and good texture.

New creativeauto accessorieswheels spraying film wheels wrap vinyl rip off car owners manufacturers wholesale