Construction procedure

In order to ensure theThe quality of the product, the customer is advised to clean the surface before use, no dust, grease; No standing water or moisture; At the same time to ensure that one side is absorbent material and solid, to ensure the paste effect.

1) cut the nozzle above the thread line to achieve the desired size and Angle (about 6mm);

2) extrude one or two consecutive strips on the back of the surface to be pasted.

3) glue the material to be pasted for at least 2 minutes;

4) wipe off the spilled glue with a wet cloth;

5) according to the different base, certain supports or fixings are still needed when bonding heavy objects.

A strip of 6mm width can be used for sizing approximately 10m;

Bonding time and strength: the final strength can be achieved after 48 hours, but may vary according to the actual situation;

Restrictions: cannot be used in damp and waterlogged areas. Cannot be used to install mirrors. Materials can be used for polyvinyl chloride; But not polyethylene or polypropylene. This product is not waterproof and should not be used outdoors.

Note: keep out of reach of children.

Storage: store in a dry and cool environment (21 degrees plus or minus 3 degrees) to prevent frost;

Shelf life: 18 months;

1. Furniture manufacturing industry: adhesive mercury lens, aluminum sealing edge, handle, crystal board, marble, board, etc.;

2,Adornment is decoratedIndustry: bonding and fixing various wood wires, door cover wires,Gesso line, floor tiles, various decorative pendants and various wall panels, and so on;

3. Exhibition industry: adhesive fixationAll kinds of calligraphy and painting, sign, acrylic, exhibition and so on.

4,Ambry door plankIndustry: adhesive crystal steel plate, etc.

This product is used for covering material, wood, gypsum board, metal, mirror, glass, plastic, rubber, baseboard, shutter, threshold, window sill, boundary post, pillar, junction box, all kinds of artificial materials,Ornamental stonesFixtures and tiles are fixed to concrete, brick, plaster, walls and cardboard.

Clean construction surfaces to ensure no oil or dust.

Cut the opening, install the nozzle, and extrude with the sealing gun.

I. dry bonding method (suitable for joints with light materials and light bearing)

1. Extrude a few lines of \"the\" shaped liquid nails at a distance of 40cm;

2. Press the side with liquid nail to the adhesive, pull it open gently, and let the glue volatilize for 2~5 minutes;

3. Then press both sides together.

Ii. Wet bonding method (suitable only for places under high pressure and with clamping tools)

1. Apply the liquid nail according to the dry bonding method;

2. Cooperate with the tongs, nails or screws to tighten the two sides immediately;

3. Remove the clamp after the glue solidifies (24 hours).

Bonding method of weight-bearing materials:

Can be directly bonded to the load material. First, glue the loading materials together, then separate them, wait for about 5 minutes to dry, and then firmly press and hammer the materials to be bonded so that they are in place. Support can be provided by support columns if necessary. (heavy materials must be supported)

Dry bonding method :(day line, foot line, door frame, background wall)

1. Extrude the \"of\" type adhesive along the adhesive surface

2. Press the sticky side against the sticky side and press both sides tightly

3. Pull apart the two adhesive surfaces and allow the liquid nail to evaporate for 2-5 minutes

4.2-5 minutes later, press again and tap gently along the joint.

5. Temporarily fix the adhesive with auxiliary tools for 24 hours and then cancel the auxiliary fixation.

6.the adhesive effect can be achieved within 24 hours and completely cured within 2-3 days

Wet bonding method :(wood floor,Marble tableEquivalent larger materials)

1. Apply the liquid nail super glue according to the dry bonding method

2. Press the adhesive surface tightly, the adhesive effect can be achieved within 24 hours, and cure completely within 2-3 days.

Quick adhesive liquid nail has super fast adhesion, especially the effect is more significant in many also surface, as long as any surface of the multi-empty structure, can achieve a fast bonding effect, no auxiliary device in the bonding process.