Packing specification: 120 PCS/carton, specification: 27x4.5x2 net weight: 66g

1) purpose: our firing gun is suitable for a variety of indoor and outdoor needs -- camping, stove, barbecue, wax, etc.
2) design: single safety lock, gas can be recharged for repeated use;
3) function: open flame. Add gas, piezoelectric ignition;

4) type: piezoelectric;
5) fire adjustment: the flame size can be adjusted, the middle of the fire adjustment ring can be opened, the fuel perspective window.

Matters needing attention

1, containing pressurized flammable gas, please keep away from children; 2, do not puncture or throw lighter, do not throw into the fire; 3. Please use it in a ventilated environment and pay attention to inflammable articles; 4, the direction of the head of fire is not allowed to face, skin and clothing and other combustible substances, in order to avoid danger; 5, when the ignition, please identify the position of the fire, the appropriate ignition. The lighter of different style USES different way to ignite: cent is straight dozen, side dozen, side dozen; The gasoline engine should quickly rub the grinding wheel, the sound machine with the thumb from right to left fast friction drum; 6, when using, if accidentally there is soot and other sundries fall into the fire, should be timely and forcefully blowing to remove sundries, otherwise it will cause bad fire; Loud sound and gasoline lighters, such as the lid opened, gas began to escape. Therefore, before ignition, please be sure to cover the machine cover to save; 8. This product is not suitable for lighting. Do not burn for more than 1 minute to avoid scalding the skin. 9. Do not keep the lighter in a high temperature environment (50 ℃ / 122 ℃) for a long time, and avoid direct sunlight for a long time, such as around the stove, outdoor closed car and trunk; 10. Due to the restriction of the climate in the area above 3,000 meters above sea level on the combustion conditions, the ignition performance of the windproof and direct impact lighters will be greatly affected. At this point, it is recommended to use open flame lighters; 11, desktop and other arts and crafts lighters in use, it should be clear that the fire mouth, press the dozen, air intake, flame regulator to do the right use; 12, should use qualified butane gas, bad gas may damage the lighter or reduce the service life.

Adjust the flame

1. When using, the flame height will change to a certain extent with the decrease of the gas content of the product and the change of the ambient temperature. This is a normal phenomenon. 2, when using, the normal flame height should be regulated in: wind and direct impact lighters for 1.5-2.5cm; Loud sound, gasoline and open flame lighters for 2.5-4.0cm; 3, if the need to adjust the flame height, please use a word screwdriver at the flame regulator groove; If the lighter itself is equipped with an adjustment ring, you can directly use your finger to adjust the arrow direction (-) clockwise rotation, can reduce the flame height; Increase the flame height by turning counterclockwise in the direction of the (+) arrow. Note: rotate counterclockwise, not more than half a turn above normal flame height. Otherwise, the product may be damaged; 4, gasoline lighter should be adjusted by the ignition wick to control the height of the flame. Flame height is too high, can use scissors to cut off a little wick; If the flame height is too low, can pull out the wick appropriately.

Aerated method

1. When refueling, there must be no sparks or kindling around, to ensure safety. Do not smoke while adding air; 2, should use qualified butane gas, bad gas may damage the lighter or reduce the service life; 3. When adding air to the ordinary machine, please stand the lighter upside down, aim the air outlet of the gas bottle at and cover the air inlet of the lighter, press it several times, and hold it for about 2 seconds each time; If the gas cannot be filled, it may be that there is excess air left in the steam tank. At this time, you can vent air, use a small screwdriver to aim at the air inlet and vent air rapidly for 1-2 times, and then conduct aeration operation. 4, sound machine in the air, please use a word screwdriver and other tools to loosen the inlet screw cover, and then follow the above steps. After aeration, screw cover can be flat, not too tight; Otherwise, the lid will not be compact and the sound of the lid is not clear, but also make the gas escape. Hardcover sound machine should use special air mouth to add air; 5, gasoline engine refueling, should open the head cover, pull out and reverse the movement, open the outer sponge to add an appropriate amount of gasoline, such as gasoline into the inner layer of cotton, cover the outer sponge, and then into the housing; 6, all kinds of lighter fuel, at least to wait 1 minute, make the newly charged gas temperature to room temperature, and wait for the remaining gas attached to the appearance of the lighter to evaporate completely before ignition. If at this time immediately carry out the ignition operation, may make the lighter appearance of the residual gas burning, causing unnecessary danger. After the resupply of gas, if the flame height is too high or too low during use, it is a normal phenomenon, the flame height can be appropriately adjusted.

Loud, gasoline lighter replacement flint

1. At ignition, Mars is too small to ignite the gas. Replacement of flint should be considered; 2. Ordinary sound machine: always press the slider to slide to the bottom of the machine cover with your finger, reverse the lighter, shake it gently, and pour out the old flint from the firestone slot and replace it with new flint; 3, install type sound machine and gasoline engine: the hardcover type sound machine flint fastening screw in the back of the head cover, gasoline engine flint fastening screw at the bottom of the movement, with a word screwdriver slowly out of the fastening screw, be sure to pinch the screw with your fingers, so as to avoid the following spring will screw top fly. After the replacement of new flint, screw into the screw, also be sure to use fingers to protect the screw and spring; 4, verify whether the correct operation: fast ignition, in order to rub the flint, if can rub out a large number of sparks, it indicates that the flint has been replaced correctly. Otherwise, the screw can be adjusted to make the flint in the correct position, then verify.

The maintenance

1. Keep out of reach of children; 2, because the use of high pressure flammable gas, so it is prohibited to be added to the percussion, or in the fire, not placed in the room temperature 55℃ above the place; 3, do not rub with other metal objects, or easy to damage the surface protection layer. Do not drop, throw or drop the product, or it may cause damage to the structure and function. 4. This product cannot be waterproof, please do not place in the water/acid/alkali/greasy or wet ring

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

 alibaba