006880 SPE-UV4050 Floor Type UV Exposing and Curing Dual Purpose Machine

UV products are increasingly used in all aspects of society, such as UV glue (no shadow glue) is widely used in adhesive, sealing, surface coating use; Completely transparent after curing, the product will remain good quality for a long time. Compared with the traditional instant dry adhesive, it has the advantages of ring resistance detection, no whitening, good flexibility and so on.

UV offset printing ink, UV screen printing ink, UV pad printing ink, UV waterborne inject ink are widely used in the printing industry, such as UV iron printing ink, UV glass ink, UV plastic ink, UV circuit printing ink, UV photosensitive ink, etc. At the same time, it has good adhesion, abrasion resistance, corrosion resistance, weather resistance and so on.

All UV adhesive or ink products curing needs a UV light source to illuminate the product, so that the product in the chemical "light starter" exposed by UV light stimulation, the chemical contained in the "monomer" generation of adhesive hardening "radiation hardening technology in a relatively short time.

The UV lamp with the wavelength of 365nm produced ,and it has a strong penetrating power.It can be used for UV curing products with wave length of 365nm (this wavelength can be used for more than 80% UV curing products, please consult the UV material supplier for special wavelength curing, so as to choose the right curing machine).

This machine can also be used for making plate . This machine is equipped with a black rubber sheet with a thickness of 0.2 cm 50cm long,50cm wide , and a glass suction chuck.

The operation methods is as follows:

1，Spread the black rubber on a flat table;

2，Place the coating mesh frame on the rubber sheet, and stick the mesh side to the rubber sheet.

3，Put the film on the top of the mesh exactly (in order to prevent the film sliding, it is best to use a little transparent tape to stick the film and the four sides of the mesh together);Use a glass sucker to lift the glass and place it on the film;

4，Move the machine to the top of the screen frame. The distance between the lower edge of the case and the screen frame is 3-5 cm.According to the actual exposure time of photosensitive adhesive to set the countdown time.

5，After the countdown, the light will automatically turn off, remove the machine, take out the glass and film, exposure is completed.

1. The machine is equipped with a dedicated ultraviolet lamp tube with the length of 44 cm, diameter of 3.2 cm, power of 15W and wavelength of 365nm 5 pieces, total power 75W, opening irradiation size of box 34*47 cm;

2. Install dual-control switch;
The first gear switch is on, the light is on; Used for UV curing;
The second gear switch is on, and the countdown meter can be used for exposing regularly.

3. Floor type structure and casters can be installed to move the machine to any area at any time;

4. This platform is a combined structure, with small packaging volume, light weight, safer transportation and lower freight cost.

5.Configuration of a full set of installation tools, customers can easily install according to the installation manual;

6. Equipped with 1 ballast and 1 lamp tube for replacement;

7.The main machine is all advanced electrostatic spraying surface treatment, corrosion resistance, resistance to scrub.

Methods of using the timer

1,Before using, please press the "C" button to reset, the display shows 00:00 00 and it is flashing state.

2,Press the "hour" and "minute" and "second" button separately to set the countdown of the electrify time, the display shows "ON"

3,Press the "start/pause" button to start the countdown.
For example: set exposure time 5 minutes 30 seconds :
At first press the "C" button to remove the original set ; Then press "minute" set to"5"; press "seconds" set to "30"; Then press the "start/pause" to start the countdown, lamp open; After five minute 30 seconds countdown , plate burning machine tube closed.
This setting do not need to change, it is automatically saved.
when the machine starts again, the countdown is still 5 minutes and 30 seconds.

Basic parameters of the timer:

Countdown: 1 SEC - 99 hours 59 minutes and 59 seconds

Working temperature: - 25 c - 65 c