About logistics

default STO Express

contact:

mr. Quan 18620268793

Watch FAQ

Why do some models have no film?

Physical stores are prone to scratches when trying to wear, and spotlights will oxidize, etc. Generally will give Watch screen protector to protect the watch. In the watch wholesale market, there are hundreds of films per pack for a few yuan. It is not to judge whether the watch is brand new. No film. If a watch is worn, many scratches will occur in a few days, and these scratches cannot be repaired. Our Watch online sales, there is no problem of selling in physical stores. There is a film when leaving the factory. If there is no film, there is no film. All products are brand new genuine goods, please feel free to use.

Why is there color difference in the picture?

All goods in this store are genuine and do not sell fake goods. The picture may be due the relationship between light and display is different, even if the same picture is on different display, there will be color difference. For example, the same image the white steel strip may appear white, gray or even black in different positions. It is recommended that all buyers buy the real product before buying buy, please can't accept any color difference at all. Buyers who are different from the actual size and imagination will buy it after considering it clearly. The counter will look at the actual product and buy it again.

Why do I need to change the battery when I just bought the watch?

Explanation1: the battery of quartz watch has been installed into the watch case at the factory, so after leaving the factory even if the battery is not purchased by the customer, there is a loss. Therefore, it is possible that the customer needs to replace it with a new battery if the purchase time is not long.

Explanation2: when the watch produces the movement, the battery is put in and started to run, and then assembled into a watch, the middle room passes through various circulation channels, and the power is continuously consumed. The watch didn't start the first second when the customer decided to buy it., it is natural that the battery is out of power in advance. The watch manufacturer has no factory date, and we don't know the time required for the intermediate circulation channel.

Why didn't I leave the watch I received?

 Generally, a three-eye timing pointer watch usually takes a long second hand, only the timing can go, just for example, when we were young, the sports teacher asked us to run. When we started, we pressed the start and the end. How much time did it take,50 the distance of meters, you can calculate the speed. This pointer means the code table, which is operated by buttons. You can go only after pressing it. Usually you don't need to let him move, no however, it costs a lot of electricity.3 one of the eyes is small dial, walking every second, that is the time second needle ~

Why does the automatic mechanical watch still need to be wound up?

The automatic mechanical watch is automatically loaded by the gravity hammer movement in the watch, but when the wrist movement is not enough or the watch when not in use for a long time, you need to manually add a strip to give the watch enough energy.

Why do some automatic watches still keep the hand bar mechanism?

This has two main functions:
1) if the number of activities of the wearers of the automatic watch is small on that day, especially some ladies, can quickly use the hand bar mechanism to tighten the clockwork, no hand the table is stopped due to insufficient power.
2) when the fault of the automatic mechanism affects the previous bar, you can use the manual previous bar to make the watch continues to be used.

12 how to adjust the point calendar?

Explanation1: first adjust the calendar to the day before, turn the pointer to make the calendar jump to the day, and then adjust the time, you can distinguish between the afternoon, and you won't jump the calendar at 12 noon.

Explanation2:1. Adjust the date to yesterday.2. Then rotate the timeline, rotate24 small Hour, jump to today's date, and then dial to today's time.

What is the reason for the second hand finger position:
hour hand is installed on the time wheel tube, minute hand it is installed on the sub-wheel tube and keeps a fixed transmission ratio through cross-wheel contact. Therefore, when the hour hand is on the whole point, the sub-needle has a point requirement. And seconds the needle is installed on the second axle and belongs to driving wheel series, which is not directly related to the minute needle (that is, the minute is for the whole time, and the second hand is not necessarily referred to in60 on the scale). However, during all the dips, you can only toggle the time division needle, not the second hand. Even if the points are for the whole point, it is installed from the zero position for seconds, and after pulling, it is also there will be incongruity. In daily life," points" the unit is enough, and it is not practical for seconds. So it is assembling" seconds" the needle is OK load anywhere

Popular explanation: This situation is very normal on ordinary quartz watches. The problem is that the second hand is not completely installed. Align the dial scale, even if it is aligned, there is a gap in the second hand drive gear, which will not align the second hand with the dial scale when it beats. But none of these ringing quartz watch moves accurately every minute60 seconds

Is it a fault that the clock is running out of time??

Both mechanical clocks and quartz watches have corresponding quality standards, there are certain errors when leaving. Clock travel time is relatively accurate, absolutely Accurate, A clock that is not bad at all is impossible., but as long as the quality standard of the clock is qualified. The clocks are verified as required before leaving the factory., verification during sales verify again, standard sale, for example, some super bad ones, adjust the proofreading before selling. Clocks vary depending on users and conditions, some will super bad after use( that is, the speed error exceeds the standard.), this is a sinking phenomenon in use., no fault, after adjustment, it can reach normal. But such the error of travel speed is too large., it cannot be adjusted to the normal standard., the attribute can fail, maintenance is required...

How to adjust the date and time correctly

1. Please do not22 point-2 point,(Some watches20 point-4 point) to adjust the date, it is easy to cause damage to the watch and incorrect calendar jump.
2. To extend the service life of the watch, many watches use slow jumps., that is, around midnight step by step, in the early morning2 it is normal to complete the jump before the point., some watches until early morning4 click complete.
3. You can adjust it if you jump the calendar in the daytime.--- if you find that the calendar jumps around noon during the day, generally, the time of the watch is fast, slow12 hours, for example, it is actually morning now.11 point, the watch was the afternoon before.11 point, you only need to dial the watch needle once., change the afternoon in the morning.
4. Generally, you need to dial clockwise when adjusting the time of the watch., do not dial counterclockwise. Counterclockwise dial watch it is easy to cause the deviation of the needle pointing of the watch (quartz two-pin type should be dialed counterclockwise).
5. Different styles of watches the adjustment method is also different., however, the morning and afternoon factors need to be taken into account when watching the adjustment strap calendar function.

Why is the watch waterproof and water flowing?

The waterproof test of watches is usually the result of the pressure test at room temperature, so in normal life, try to avoid using in humid environment with large temperature difference changes. The waterproof parts of the watch are matched with metal materials and non-metal materials. Composition. Under normal temperature, once the environment with large temperature difference changes, because the thermal expansion and cold contraction coefficients of the two different materials are different, their the deformation is also different. In this case, cooperation may cause problems. If you encounter soap water with high permeability at the same time, water will enter. When returning to normal temperature after the waterproof parts cooperate with the recovery, continue to waterproof. But the water has already entered and cannot be discharged any more. Once moisture enters the table in use, you need professional maintenance center for cleaning and maintenance or dehumidifying waterproof recovery