function

description

network access

when the product is out of the net, press button for a long time. When 5s enters the distribution mode, you can join the device terminal through the mobile phone APP. (Note: The device can access the network through SmartConfig and AP, and can switch to the network mode and enter the network status through button)

outbound

when the product is in the network, the device can be removed from the network by button of the device. After the device is out of the network, the product is restored to the factory settings.

Work/Sleep switching

after power on, the MCU enters the sleep mode. When a PIR detection interrupt is triggered, the MCU wakes up, turns on the WiFi power supply, uploads the PIR alarm information to the WIFI, and after the WIFI sends back the shutdown command, after completing a report operation, the MCU determines the PIR detection situation. No one turns off the WIFI power supply and automatically enters the sleep mode. Wait for the next PIR to trigger. Someone will report the cycle again.

Report battery power

when PIR triggers the wake-up MCU, the power and PIR alarm information are reported at the same time.

Low battery alarm

insufficient battery power: an alarm is sent when the battery is lower than the set minimum voltage value (insufficient battery).

OTA

available the software of the WIFI network upgrade product.

Restore factory settings

restore all configurations to the default value and exit the network.

action definition

status

action time interval (seconds)

long press( >5s

in-Network

long press, restore the factory parameter settings, and go out of the network, enter SmartConfig distribution mode

out-of-network

long press switch between SmartConfig and AP distribution mode

flashing mode

definition

long extinction

power on, after normal startup, LED long light off

slow flash

long press button to enter AP in the distribution mode, LED slow flashing state

flash

long press button to enter LED flash status in SmartConfig distribution mode

flashing mode

definition

slow flash

every1.5S flashing once

flash

every blink once in 0.2 seconds

serial Number/NO

project

Items

parameter

Parameter

unit

Unit

remarks Remark

1

operating temperature

Operating Temperature

-10 ~ +45

℃

2

storage Temperature

Storage Temperature

-20 ~ +85

℃

3

storage Temperature

Storage Temperature

8~80

%RH

serial Number/NO

project

Items

parameter Parameter

remarks

Remark

most small(Min.)

typical(Typ.)

max(Max.)

1

USB power supply

( USB Powered)

--

5V

2

battery powered

( Battery Powered)

4V

6V

3

work current

Standby Current

65mA

80mA

85mA

4

standby current

Standby Current

38uA

40uA

55uA

5

default battery capacity

Default Battery Capacity

1200mAh

1300mAh

--

serial Number/NO

project

Items

parameter Parameter

remarks

Remark

minimum(Min.)

typical(Typ.)

max(Max.)

1

sensing distance

Detection Distance

--

10m

12m

2

induction angle

Detection Angle

--

120 °

--

3

sensitivity level

Sensitivity Level

1

8

8

serial Number/NO

quality requirements

Quality Requirements

standard Description Standard Declaration

remarks

1

battery Test

(USBInsulation Test)

in USB input plus 5V/500mA, working normally

2

short circuit protection

(Short-circuit Protection)

after the two ends of the power supply are connected in reverse, the battery does not heat up and returns to normal operation after alignment.

3

overcurrent protection

(Overcurrent Protection)

the power supply does not heat up after short circuit and returns to normal operation.

4

electrostatic interference test

( ESD Test)

contact discharge± 4kV, air discharge ± 6kV, no signal should be sent during the test to interfere with the working state of the host, and after the test, the prototype should not be damaged or crashed, and normal operation can be carried out

5

ripple and noise test

(Ripple and Noise Test)

≤ 100mV

6

appearance inspection

(Visual Inspection)

the appearance of the product should be bright, and no batch front, welding line, flow mark, flower removal, scratch, and obvious shrinkage are allowed. No abnormal sound is allowed in shaking the product.

7

size and weight

(Dimensions & Weight)

size as shown in the picture above, the weight is determined after the final molding

8

drop test

(Drop Test)

free fall test, at the height of 0.5m, Take 6 sides to fall once. When falling, the function and appearance should be undamaged. After falling, all functions and appearance should be normal.

9

vibration Test

(Vibration Test)

finished product with complete packing box, put it on vibration test machine for testing1 hour, the product (appearance and function) and packing box are complete, and can meet the shipping requirements.

10

salt Spray Test

(Salt Spray Test)

metal Material part24h

11

button life test (Keypad Life Test)

short by product button 8000 times, and the interrupt can be triggered normally after the test.

12

antenna Test

(Antenna Test)

whether the outdoor distance is reached 130 meters, packet loss rate less than 5%,

serial Number/NO

test item

Items

test conditions

Test Condition

inspection items

Inspection Items

remarks Remark

1

high temperature storage

( HighTemperature Storage)

1. Under the condition of 70℃, 2 hours

2. No packaging, no power supply

1. Appearance

2. Electrical performance (normal temperature recovery for two hours, normal operation)

2

low temperature storage

( Low Temperature Storage)

1. -40 ~ ± 5 ℃,2 hours

2. No packaging, no power supply

1. Appearance

2. Electrical performance (normal temperature recovery for two hours, normal operation)

3

high temperature working test

High-Temperature Operation Life Test)

1. Under rated conditions

2. Ambient temperature 40℃

3. Humidity 85%;

1. On/off output voltage

2. Normal performance

4

low temperature working test

Low-Temperature Operation Life Test)

1. Under rated conditions

2. Ambient temperature-10 ℃

1. Device appearance

2. Normal performance