(1) the battery mount
transmitter
① unscrew the 2 fixing screw on the back, remove the casing on the back of
② take out the circuit board inside
③ battery (smooth side) Insert the battery holder.
④ keep tabs on the inner wall of the battery holder on the side of the battery for the battery coincides with the battery completely, insert the circuit into the shell.
接收机
① thumb slightly hard push back part 0
② batteries arrived in spring on the side of tight, load the battery 1.5V batteries
③ put battery cover on the shell
(2) battery test
the transmitter
switch to ON, flashing red lights. When the lights brightness is an obvious dark, can determine low battery, replace the battery.
接收机
To S-ON receiver is looking for State, after the receiver receives the transmitting signals, lights flashing, police sound, vibration motors significantly.
On indicates that the battery may load guards against losing work.
(3) battery replacement instructions
(periodically check the working condition of the product is normal, low)
recommends replacing the battery: 3V CR2032 transmitter
receiver 1.5V AAA SIZE
① transmitter signal light is Dim or no signal
→ the transmitter battery replacement
alarm sound faint, ② receiver distance not stable
→ Receiver replace batteries
③ ON receivers to prevent lost, weak red lights Dim, flashing unknown
→ receiver to replace the battery
(4) note
① when air in the airplane, please stop using it.
② After using for a long time, remove the battery, in a cool and dry and extend battery life.
③ the product launch wave is 1mW, would not cause any harm to the human body. When you use tone or vibrating alert of police, please note that this product do not confused with other sounds such as the signal to prevent accidental loss.
④ Note that waterproof.
⑤ transmitter on protected objects must wear well, so as not to separate from the protected object, cannot ensure the security of protected object to set the distance.
⑥ product using a wide, but less than 3 years old a child must be under the supervision of parents.
⑦ This product falls from heights, and other non-factory-quality problems such as rigid body collision, failure is not in warranty coverage.
(5) product description
the transmitterform factor: 44 (h) x28 (w) x8 (d) mm
weight: 9.3G
receiverform factor: 60 (h) X36 (w) x15 (d) mm
weight: 35.5G
cell: X1 7th battery
range of application: 0 ~25M (usually is refers to around no special of wireless obstacles factors Shi of applies distance)
battery life: receiver: 1 days 8 hours using, each minutes 32 times tips about 2 months around
transmitter: 1 days 8 hours using about 3 week around
total weight about 65.8g
packaging specifications 200 (h) x80 (w) x17 (d) mm
※ attached battery, and detection description and the replaced indicates
Note: the wireless barriers included metal wall buildings, tram car body, there are radio waves passing objects, set the distance will be shorter or longer change in the interference.
When used according to the environment and objects set up proper safe distance.
Method of application:
1, drop-proof function: the receiver control wheel to the maximum receiving distance, turn power switch to: "anti-lost N-ON" issued "di" a boot tone, followed by receivers issued: "di ... Di ... "wait for the beep, when net transmitter power switch to ON, transmitter signal lights flashing, start sending signals, issued after the receiver receives a signal:" di di "two tone of academic success, and flashing lights, said learning to code successfully.
Note: If the receiver power on (when the transmitter is in a shutdown state) made "di di" two tone of academic success, check to see if there are other transmitters in the work. If after turning on the transmitter, the receiver also was issued: "di ... Di ... "wait for the beep, and indicated that they had not learned the transmitter signal. Check that the control wheel position is allocated to the correct orientation, whether the transmitter is working properly.
2, learning the code after the success of promoting the distance adjustment wheel, set the corresponding protected object suitable distances recommended distances are generally installed in bags, wallets and other items about 3 meters, children or pet animals are relatively far away, according to custom.
3, when protected objects leave the set distance, the receiver alarm (a police audio tips, vibration flag product vibration and sound of police tip).
4, looking for function: set when the power supply to S-ON search function; transmitting signals within the reception range, when the receiver receives a signal, the receiver sent "di di di di" sound of police close to the tone and vibration (vibration), protective objects easily found if transmitting signals outside the receiving, receiver lights lit, don't make a sound of police. Promote adjustment wheel you can set the distance up or down
5, wear the transmitter on the body of protective objects, receiver peiyu or master.
