|
Span; style= <
product contains a sticky glue gun, chain three, a nut, a bracket, a glue stick. (glue stick plus)
1, clean with a damp cloth to clean the dent part;
2, the hot melt adhesive rod from the hot melt glue gun back loaded, buckle the trigger, let the glue stick into the glue gun, plug in the power, preheating of the glue guns for 5 minutes;
3, to find a suitable traction pads (which requires a big dent in large traction pads. (Note: traction pads is bigger, the traction force greater);
4, the snap of the glue gun trigger with extruded glue coated with selection of traction pads (gasket hole 4 should be coated with hot melt adhesive
5 and quickly coated with hot melt adhesive traction pads placed in the central part of the dent, pressed gently, until the hot melt adhesive curing cement; (hot melt adhesive to dry for about 8 minutes. We recommend that you do not let the hot melt adhesive to dry time should not exceed 10 minutes)
6, the traction tension bridge in the middle of the hole is aligned with the cement traction pads rod and the screw rotary knob is sheathed in traction pole shims, slowly tighten until the dent part to pull with the surrounding surface can be flush with the.
7, some dents, may need to repeat several times, in order to dent repair.
8, if the repair surface is raised a little, please according to the following steps: first with the thumb back and forth friction convex point until the convex point with other surface as smooth; if with the thumb cannot let convex point to restore smooth, using stick percussion (holding the pen position) gently click convex point, until the convex point restore smooth. Sometimes it may be repeated several times. (Note: the use of percussion stick, do not force too much)
9, dent repair after, unscrew the screws rotate button and remove traction tension bridge and then traction pads, if there is hot melt adhesive on the surface of the body, let the hands gently you can tear up.
1, use a wet cloth to clean the clean part of the dent;
2, the hot melt adhesive rod from the hot melt adhesive gun, pull the trigger, so that the glue stick into the glue gun, plug in the power, so that the glue gun preheat 5 minutes;
3, find a suitable traction pads (which requires a big dent in large traction pads; (Note: traction pads is bigger, the traction force greater);
4, the snap of the glue gun trigger, with the extruded glue coated with choice of traction pads (gasket hole 4 to coated with hot melt adhesive); (Figure 1)
5 and quickly coated with hot melt adhesive traction pads placed in the central part of the dent, gently pressed, until the hot melt adhesive curing cement; (hot melt adhesive to dry for about 8 minutes; we recommend that you do not let hot melt adhesive to dry for no more than 10 minutes; winter dry time slightly shorter. ) (Figure 2)
6, the traction tension bridge in the middle of the hole is aligned with the cement traction pads rod, the nut knob set in traction pole shims, slowly tighten until the dent part to pull with the surrounding surface can be flush with the; (Figure 3)
7, some dents, may need to repeat several times, in order to dent repair;
8, such as post repair surface raised, please according to the following steps: first with the thumb back and forth friction convex point until the convex point with other surface as smooth; if with the thumb cannot let convex point to restore smooth, using stick percussion (holding the pen position) lightly click convex point, until the convex point restore smooth. Sometimes it may be repeated several times. Note: when using the tap, you can't force too much.
9, dent repair and unscrew the nuts knob, remove the traction tension bridge and then traction pads, if there is a hot melt adhesive on the surface of the body, let the hands gently you can tear up.
|
