This is certain, and it would be nice if you don't answer these few questions professionally:

1. Do I need razor barbed wire, barbed wire?

2. How high does the barbed wire need to be? Regular 1.5m 1 .8m

3. How many beams do you need? Above, below, in the middle or not

4. Is the ground concrete or ground?

5. The length required, do you need a door?

6. Are there any other special requirements?

If you don't understand, the above questions are finished. The following questions are more complicated and professional! If you don't understand, the above questions are answered at the end, and the following are more complex and more professional!

Introduction of various materials and accessories:

1. Chain link fence/Chain fence mesh

2. column/Post

3. beam/Beam

4. Wire Barbed Wire/Barbed Wire

5. blade barbed wire/Rozar barbed wire

6. Barbed Wire bracket Barbed Wire stent
   

7. flat Iron/Strap

8. partial Card

9. Front Card bucket

10. casing/Beam Connection Beam

11. column ear/Beam Connection Post

12. Beam cap/Post Connection Beam

13. Wire turnbuckle/Wire tender
    

14. rain hat/Post Head

15. binding silk /Binding Wire

1. Chain link fence/Chain fence mesh

material(Material):

hot-dip galvanized iron wire galvanized iron PVC wire

wire Thickness (Thickness):

2mm-5mm

hole:

2 "2.5"

Width:

1.2m 1.5m 1.8m 2m 4 feet 5 feet 6 feet 7 feet

2. Column/Post

(Embedded column)

  The column is generally 60mm galvanized pipe, and the spacing is generally 3M. If the installation site is land, it is suitable for embedded column. The embedded column is generally 30cm-50cm longer than the net according to the actual situation such as the height and tensile strength of the net.. The installation site is concrete or asphalt pavement. Generally, flange site columns are selected and fixed with expansion screws!

 (Chassis column)

Column generally choose 60mm galvanized round tube, the spacing is generally 3m a, the installation site is suitable for embedded columns, embedded columns according to the height of the net tensile strength and other actual situations are generally longer than the net 30cm-50cm. The installation site is concrete or asphalt pavement generally using flange site columns, fixed with expansion screws!

3. Beam/Beam

the beam is generally 48mm galvanized pipe with a length of 6m or 3m.

Beams are generally 48mm galvanized round tubes with a length of 6m or 3m.

4. Barbed Wire bracket Barbed Wire stent

Double arm barbed wire bracket, fixed wire barbed wire and blade barbed wire.

Double-arm barbed rope bracket, fixed wire barbed rope and blade barbed rope.

5. Wire Barbed Wire/Barbed Wire

iron wire barbed wire  Hot dip galvanized low carbon steel wire, coarseness 12# 14#. Wire barbed wire Hot-dip galvanized mild steel wire, thickness 12# 14#

6. Blade barbed wire/Rozar barbed wire

spiral cross blade barbed wire C ross Razor Barbed Wire

7. Flat Iron/Strap

for chain link fence the beginning part and the end part are connected to the column through the offset card, passing through chain link fence make the upper and lower forces of chain link fence evenly. Used for the beginning and end of the hook net, connected with the column through the offset card, through the hook net so that the hook net up and down the force is uniform

the connection between the beam and the beam can be directly put together.

The connection between the beam and the beam is just a good way to put it together.

11. Column ear/Beam Connection Post

the connection between the beam and the beam can be directly put together. At the beginning of the beam, the end or corner is connected to the column through the positive card.

The connection between the beam and the beam is just a good way to put it together. At the beginning, end or corner of the beam is connected to the column by a positive card

12. Beam cap/Post Connection Beam

When there is no barbed wire bracket on it, it is used on the column to measure the passing through. When the barbed rope bracket is not placed on it, it is used to measure the upper pole to pass through it.

13. Wire turnbuckle/Wire Tender

 ( galvanized Wire turnbuckle/Wire Tender)

14. Rain hat/Post Head

When there is no barbed wire bracket and other accessories on the column, it is buckled on the top to prevent rainwater from entering the column When there are no barbed rope brackets and other accessories on the top of the column, it is fastened to prevent rain from entering the column

15. Binding Wire/Binding Wire

it is used for fixing barbed wire and column, fixing between barbed wire and beam, fixing of iron wire barbed wire and barbed wire bracket, fixing of blade barbed wire and iron wire barbed wire, and temporary binding and fixing during installation.

It is used for the fixing of barbed wire and columns, the fixing between barbed wire and beams, the fixing of wire barbed rope and barbed rope bracket, the fixing of blade barbed rope and barbed wire rope, and some temporary bundling during installation.

Construction and Installation steps:

Construction and installation steps:

1. Determine the location and dig holes

1. Determine the location and dig the pit

  It is recommended that the hole size is 30cm wide * 30cm long, and the depth is the length of the column minus the height of the mesh surface plus 5cm. For example, for 1.8m high net and 2.1m column, it is recommended to dig 35cm deep, and the column is embedded 30cm, when the pit depth is 5cm, the overall height can be adjusted up and down, and the concrete with a thickness of 5cm can be poured more firmly at the same time.

It is recommended that the pothole size is 30cm wide * 30cm long, the depth is the column length minus the mesh height plus 5cm, such as 1.8m high net, 2.1m column, it is recommended to dig 35cm deep, the column is buried 30cm the pit depth of 5cm can be adjusted up and down when installing the overall height, while pouring more 5cm thick concrete is also more firm.

2. Put the column

2. Put the POST

Fill in three quarters of concrete. After pouring part of the column, adjust the column in a straight line as a whole. At the same height, after adjusting, the cement fills the hole and fine-tune it again, handle some columns encountered when adding concrete later. If it is not firm, it can be supported and reinforced.

Fill in three-quarters of the concrete, after the column is poured, adjust the column as a whole in a straight line, at the same height, adjust cement to fill the pit, fine-tune again, and deal with some of the columns encountered when adding concrete later. Support reinforcement can be performed if it is not strong.

3. Stand for 5-7 days to ensure that the concrete is dry.

3. Let stand for 5-7 days to make sure the concrete is dry thoroughly.

Add a beam below to make it firmer. Add beams below for a firmer fit

4. The barbed wire bracket is inserted on the column, and at the same time, the upper beam passes through the middle of the barbed wire bracket. The first beam and the column are connected to the column through supporting ears, and the rear beam is connected by casing, bend or last the beam and the column are connected to the column through supporting ears.

The lower beam and the beam added in the middle cannot pass through the middle of the column. The length of the beam is the distance between the two columns. The connection method is both a column and a partial clamp, A column ear is fixed with one end of the beam.

4.  The barbed rope bracket is inserted into the column, and the upper beam crosses through the middle of the barbed rope bracket, the first beam and the column are connected to the column through bias card column ear, the back beam is connected with a casing between the beams, and the bend or the last beam and the column are connected by the bias card column ear and column.

The lower beam and the middle beam cannot pass through the middle of the column, the length of the beam is the distance between the two columns, and the connection method is all a column, a bias card, and a column ear is fixed with one end of the beam.

5. Install barbed wire

5. Install the wire mesh

the barbed wire opens the flat iron and passes it through one head of the barbed wire as a whole. It is linked to the column through partial clamping, and then the barbed wire is tightened (make sure that the concrete poured before this step has been dried out and firm, otherwise all previous achievements will be abandoned), check which wire at the end of the tensioned barbed wire is close to the nearby column, and then the flat iron passes through the wire to remove the excess barbed wire. The length is not enough and needs to be manually lengthened. The flat iron and the column are fixed by using the partial clamp. The barbed wire must be tightened. If it is not tightened, the firmness will not be beautiful. You can use wire turnbuckle to shrink.

The barbed wire is opened The flat iron passes through the barbed wire as a whole, is linked to the column through a bias card, and then the barbed wire is tightened (before this step to ensure that the concrete that was previously poured has dried firmly and firmly, otherwise the previous work is abandoned) check which wire at the end of the tightened barbed wire is close to the nearby column, and then the flat iron passes through the wire to extract the excess barbed wire. Insufficient length also requires manual lengthening. Use a bias card to fix the flat iron and the column. The barbed wire must be tightened if it is not tightened, the firmness will decline and it will not be beautiful. Shrinkage can be carried out with the help of a wire tensioner.

6. Reinforce barbed wire

6. Reinforced barbed wire

utilization binding wire  will barbed wire tied with the beam. When binding, the upper beam should be tied with the intersection of the wire mesh with a lower upper horizontal beam half grid or one grid, forming a pulling force with the wire mesh to ensure that the beam will not slide, at the same time, the barbed wire mesh surface is leveled. When binding the lower beam it should be tied to the intersection of half-grid or one-grid barbed wire mesh on the lower beam. Middle barbed wire no flat iron is fixed with the upright post, just fix the barbed wire and upright post directly binding wire.

The use of wire to tie the barbed wire and the beam together, when bundling, the upper beam should be tied with the lower upper beam half or one block of the barbed wire mesh intersection, and the barbed wire to form a pulling force, to ensure that the beam does not slide but also to flatten the barbed wire mesh. The lower beam is bundled at the intersection of the barbed wire mesh half or one block above the lower beam. The middle barbed wire mesh does not have a flat iron to fix the column, and it is enough to directly tie the wire to fix the barbed wire and the column.

7. Install barbed wire

7. Install the barbed rope

z-type gap is directly stuck in, not easy to disengage, easy to install. The Z-shaped opening is directly stuck in, not easy to disengage, and easy to install.

You must wear gloves, preferably leather gloves, to prevent stab wounds and cuts. Don't underestimate the power of this barbed wire, redlon barbed wire it is very sharp. There are chemicals left on the surface of barbed wire galvanized, and small wounds are also very painful. Open the wire barbed wire, fix one end, and then iron wire barbed wire stuck at the Z-shaped gap of the barbed wire bracket until it is fixed at the end. Iron wire barbed wire after all are installed, open the blade barbed wire, put it on the wire barbed wire, fix the blade barbed wire and wire barbed wire with binding wire in turn, and fix blade barbed wire iron wire barbed wire fixed together with barbed wire bracket.

This must wear gloves, preferably leather gloves, to prevent puncture cuts, do not underestimate the power of this thorn rope, Ledron thorn rope is very sharp, the surface of the thorn rope has the chemical residue during the galvanizing treatment and the small wound is also very painful. The wire barbed rope is opened, fixed at one end, and then the wire barbed rope is stuck in turn at the Z-shaped opening of the rope holder until the end is fixed. After all the wire barbs are installed, open the blade barb rope place it on top of the barbed wire barbed rope, and fix the blade barb rope and the wire barb rope with the wire in turn, and fix the blade barb rope together with the barbed rope bracket.

8. Door installation

8. Installation of doors

 (Double-door 2m 3m 4m)

the installation of the door is mainly to measure the actual width of the well-done door on the ground, and keep the positions of the columns on both sides. Then, it will be good to directly dig the pit and embed the concrete, you can tighten the wire barbed wire and place the blade barbed wire above the upright posts on both sides. Like other walls, if there are high cars entering and leaving, do not install barbed wire on them.

The installation of the door is mainly to do the door, put on the ground to measure the actual width, the two sides of the column to leave a good position, then directly dig the pit concrete embedded pouring is good the two sides of the column above can be tightened wire barbed rope place blade barbed rope, and other wall positions, if there is a high car in and out, do not install barbed rope on the top.

 (Single door 1m 1.5m 2m)

9. Closing

the column without barbed wire bracket is buckled rain hat. After installation, check later, lower corner material and cleaning. The work is beautiful, and the end should also be beautiful. What is it like, whether it is good or not.

9. FINISH

The column without the stinging bracket buckles the rain cap. After installation, post-inspection, scraping and hygiene cleaning. The work is done beautifully, and the finish should be beautiful, what is it, what is it like to do well, or what it is.

Believe in professional power!

We are serious about making silk screen!

Silk Screen please select Redlon!

Redlon goes with you!!!

Believe in professional power!

We are serious about making wire mesh!

Good  wire mesh wire mesh,  please choose REEDRLON!

REEDRLON with you toghter! ! !