2. Standby: Use the four fingers of your right hand to support the base, and place your thumb naturally on the top of the body cover, holding the entire machine smoothly.
3. Thread: At the bottom of the product description, there is a picture;

4. Lay the fabric: Lift the press plate with the index finger of your right hand, place the prepared fabric to be sewn flat under the press plate, and gently replace the press plate to press the fabric.
5. Sewing Operation: Hold the fabric with your left hand, and press down lightly and quickly with your right thumb, allowing the feed mechanism to automatically push the sewn item to the left. Keep the right hand holding the machine still, let the machine feed the fabric by itself, and control the direction of the fabric with your left hand to maintain a straight stitch until the sewing is complete. This machine can automatically feed the fabric and adjust the tension between the stitches.
6. Knot Tying: If the single-thread sewing machine needs to be tied, the method of knot tying is on the upper right corner of page 3 of the instruction manual.
7. Change the thread group: simply pull it out, be careful not to lose the spring, if you need to change to a larger thread group, you can connect the spare extending rod to the thread tube shaft, insert the larger thread group, and then re-thread the needle, adjust the tension of the thread after sewing.
8. Change the needle: Loosen the fixed screw, remove the broken needle, and install the new needle.

Commonly encountered problems and their solutions

Problem one: The needle skips, and there's nothing on the back, the needle is empty, and on the front it's just a straight line. It falls off when you pull it!

Solution: If the needle jumps and falls off when pulled, it is inevitable, as the thread on the back has not been looped through. Normally, the loops should be secured. The problem with the needle jumping is that the speed of the fabric entering is too fast, and the machine cannot catch up to secure the loops on the back. Keep your hands holding the machine still, let the machine enter the fabric by itself. If it still goes straight, you need to adjust the machine! If you don't know how, please contact customer service, and we will teach you!

Problem 2: There's a bunch of lines on the back, it's stuck!

Solution: There's always a bunch of lines on the back, and it always gets stuck, preventing the machine from moving. The reason is that the fabric is being fed too slowly. Keep your hands on the machine still, and pull the fabric to the left side of the machine to speed up the feeding process. This will solve the problem.

Question 3: I keep losing connection or the stitches are really loose!

Solution: If you constantly experience disconnections, make sure to only thread the wire through positions 1-3-4. Do not place the wire in position 2, as it will definitely break if it is clamped there.

1. Sewing machine jump thread, how to repair the broken thread
You must have worn thick socks. It's likely that the sewing time was wrong. First, check if the needle is crooked. Crooked needles can also cause this problem.

Jumpers:
1. Incorrect threading method. Please re-thread according to the "threading diagram".

2. Incorrect installation of the straight needle - Check the needle height and orientation, ensuring that when the needle moves downward, it is slightly in front of the needle plate hole.

3. The needle tip of the straight machine needle breaks or bends. Replace the new machine needle.

4. If the tip of the curved needle becomes dull, use an oil stone or fine sandpaper to sharpen it, or replace the new curved needle.

5. The tension of the suture is too large or too small. Adjust the tension of the suture appropriately.

6. The curved needle cannot capture the loop of the straight needle on the right side, and the right side of the lower decoration line jumps the needle. The loop of the straight needle is too small, and the jump line quantity should be appropriately increased.

7. The curved needle cannot capture the loop of the straight needle on the left, and the left stitch of the lower decoration thread jumps. The loop of the straight needle is too large, reduce the amount of jumping thread appropriately.

8. The curved needle cannot simultaneously hold the middle and left straight needle loop, and the middle and left thread traces of the lower decoration line jump needles. Reduce the amount of jumping threads appropriately.

9. The middle of the back of the curved needle, the left needle thread cannot be threaded into the triangular shape formed by the knitting needle thread and the curved needle thread. The middle of the back of the left thread trace jumps through the needle. Check if the seam thread has passed through the bobbins, and check the synchronous operation of the bottom thread cam. If there are any problems, adjust according to the standards.

10. Incorrect combination of the straight needle and the curved needle - Check the height of the needle bar, the synchronization between the straight needle and the curved needle, and adjust as needed according to the standards if there are any issues.

11. Misalignment of the needle with the needle guard check the position of the needle and the needle guard

12. Incorrect combination of the machine needle and the basting needle or incorrect position of the basting needle can cause the decoration thread to skip stitches. Check the size of the machine needle and basting needle combination, and check the amount of thread coming out of the basting needle.

Three, Line Break

1. Incorrect threading method. Please re-thread according to the "threading diagram".

2. Incorrect installation of the needle. Reinstall the needle, ensuring that the needle groove is directly facing the operator.

3. The needle eye and needle groove of the sewing machine are not smooth. Replace the new needle.

4. Tension of the suture is too high. Adjust the tension of the suture appropriately.

5. The quality of the suture is too poor. Replace with better suture.

6. The thread is thicker than the needle hole, use a suitable thread or sewing machine needle.

7. The threading holes of the machine needle, bend needle, needle plate, presser foot tongue, and threading holes may have burrs or scratches. Use a oil stone or fine sandpaper to re-polish, or replace the damaged machine parts.

8. Incorrect coordination between the needle and the bent needle, the tension needle. Adjust the coordination according to the standard for the needle and the bent needle, the tension needle.

Fourth, broken needle

1. The pressure of the presser foot is too low, causing the fabric to be delivered poorly and leading to broken needles. Increase the pressure of the presser foot appropriately to ensure normal fabric delivery.

2. If the curved needle collides with the straight machine needle, adjust the position of the curved needle and straight machine needle according to the standard.

3. If the binder needle collides with the straight machine needle, adjust the position of the binder needle and the straight machine needle according to the standard.

4. Misalignment of the straight needle with the needle guard bar Adjust the alignment of the straight needle and the needle guard bar according to the standard.

5. Bend needle tip is round and bald, replace with new bend needle.

6. The needle bar and needle bar sleeve wear too much, causing the loose fit between the needle bar and the needle bar sleeve. Replace the needle bar and the needle bar sleeve.

7. The needle holes on the needle plate are too small. Update the large needle hole needle plate or change to a smaller size machine needle.

8. The loose fit of mechanical components is large. Check the fit and wear condition between the hook line mechanism's components, adjust the dimensions according to the standards, and replace the severely worn components.